Hi

I bought a 90s Rocky Mountain Summit to restore
The bits are all good, bearings rough as, but i've mostly fixed them up
I just discovered that the chainstay has rust holes in it so the frame is trash
It's a bit of a shame as I never even got to ride it but the project has been fun anyway
It's got 7 speed XT on it, a bunch of ritchey parts etc and i've bought all the consumable cables, brakes etc
Does anyone have a nice large or xl 26" rigid frame they would part with that i can put it all on?
it'd be a shame to go nowhere with this

Cheers

potentially i could maybe be persuaded to part with a circa 1991 Marin Muirwoods frame. she was my first mtnbike, served mountain bike duties from 93 to about 98, then used as a commuter from then til the early 00s, and has been hanging around in my garage(s) since... BB is still in it, square taper, and still spins smoothly (i think, been a while since i turned her over, haha). seatpost with it too. oh, and has a lot of interesting mid-90s stickers all over it too.

not sure what the value of such a priceless family gem is...

I'm no frame builder, but can't that be patched or replaced?

Or is it the case that it is un-economic to continue with the frame?

swtchbckr wrote:potentially i could maybe be persuaded to part with a circa 1991 Marin Muirwoods frame. she was my first mtnbike, served mountain bike duties from 93 to about 98, then used as a commuter from then til the early 00s, and has been hanging around in my garage(s) since... BB is still in it, square taper, and still spins smoothly (i think, been a while since i turned her over, haha). seatpost with it too. oh, and has a lot of interesting mid-90s stickers all over it too.

not sure what the value of such a priceless family gem is...

how about a box of beers and knowing it will be ridden once again : )
are you in Auckland?
can you post a photo?
I could do some cash your way too

Rik wrote:I'm no frame builder, but can't that be patched or replaced?

Or is it the case that it is un-economic to continue with the frame?

I think it rusted from the inside out so it's hard to know how bad the damage is.
I'm thinking about it though.
Either, nuke the inside with rust inhibitor, spray rust converter primer on the outside and give it a bit of paint and hope for the best.
Or do that and get someone to shoot some tig or mig wire in it
Getting a new chainstay welded in is doable even but probably not worth it.

I think i'd be more keen if i had a sentimental attachment to the frame but I haven't even ridden it yet.
And i'd be more keen just to chance it if i was the only one riding the bike, but i'll end up letting different people borrow it and I don't want to have to say for them to check it for frame cracks each time.

I dunno

nevermind actually
a local shop said they'd weld it

Mosey wrote:

swtchbckr wrote:potentially i could maybe be persuaded to part with a circa 1991 Marin Muirwoods frame. she was my first mtnbike, served mountain bike duties from 93 to about 98, then used as a commuter from then til the early 00s, and has been hanging around in my garage(s) since... BB is still in it, square taper, and still spins smoothly (i think, been a while since i turned her over, haha). seatpost with it too. oh, and has a lot of interesting mid-90s stickers all over it too.

not sure what the value of such a priceless family gem is...

how about a box of beers and knowing it will be ridden once again : )
are you in Auckland?
can you post a photo?
I could do some cash your way too

only just spotted this... I'll chuck a photo on when i get home. Alas, i'm in Churchur.